ページ先頭

本文

CX-One Ver.4 各ソフトウェア
更新内容詳細

Change history of Common Module

- :CX-One Version 4 Auto-update (March 2014)

New functions

[CPS]

  • Added the following files.
    CPS_E5GC_Ver0_0.xml

- :CX-One Version 4 Auto-update (January 2014)

New functions [Cmn1401_0401Setup.exe]

[CPS]

  • Added the following files.
    CPS_NJ301-1100_Ver1_8.xml
    CPS_NJ301-1200_Ver1_8.xml
    CPS_NJ501-1300_Ver1_8.xml
    CPS_NJ501-1320_Ver1_8.xml
    CPS_NJ501-1400_Ver1_8.xml
    CPS_NJ501-1420_Ver1_8.xml
    CPS_NJ501-1500_Ver1_8.xml
    CPS_NJ501-1520_Ver1_8.xml
    CPS_NJ501-4300_Ver1_8.xml
    CPS_NJ501-4310_Ver1_8.xml
    CPS_NJ501-4400_Ver1_8.xml
    CPS_NJ501-4500_Ver1_8.xml
Improved functions [Cmn1401_0402Setup.exe]
  • You can use the updates of following Support Software after installing this update.
    Sysmac Studio
    CX-Motion Pro V1.43 or higher
    CX-Drive V2.92 or higher
    CX-ConfiguratorFDT V2.00 or higher
  • You must restart your computer after installing this update.

- :CX-One Version 4 Auto-update (September 2013)

New functions [Cmn1309_0401Setup.exe]

[CPS]

  • Added the following files.
    CPS_CJ1W-SPU01_Ver2_2.xml
    CPS_CS1W-SPU01_Ver2_2.xml
    CPS_CS1W-SPU02_Ver2_2.xml
    CPS_NJ301-1100_Ver1_7.xml
    CPS_NJ301-1200_Ver1_7.xml
    CPS_NJ501-1300_Ver1_7.xml
    CPS_NJ501-1320_Ver1_7.xml
    CPS_NJ501-1400_Ver1_7.xml
    CPS_NJ501-1420_Ver1_7.xml
    CPS_NJ501-1500_Ver1_7.xml
    CPS_NJ501-1520_Ver1_7.xml
    CPS_NJ501-4300_Ver1_7.xml
    CPS_NJ501-4310_Ver1_7.xml
    CPS_NJ501-4400_Ver1_7.xml
    CPS_NJ501-4500_Ver1_7.xml
Improved functions [Cmn1309_0401Setup.exe]
  • Solved the problem that a success message was displayed when a Clear All Memory Areas operation was executed for a CJ2 that had an I/O Bus Error.
Improved functions [Cmn1309_0402Setup.exe]
  • You can use the updates of following Support Software after installing this update.
    CX-Motion Pro V1.43 or higher
    CX-Drive V2.92 or higher
    CX-Configurator V2.00 or higher
  • You must restart your computer after installing this update.

- :CX-One Version 4 Auto-update (June 2013)

New functions

[CPS]

  • Added the following files.
    CPS_NJ301-1100_Ver1_6.xml
    CPS_NJ301-1200_Ver1_6.xml
    CPS_NJ501-1300_Ver1_6.xml
    CPS_NJ501-1320_Ver1_5.xml
    CPS_NJ501-1400_Ver1_6.xml
    CPS_NJ501-1420_Ver1_5.xml
    CPS_NJ501-1500_Ver1_6.xml
    CPS_NJ501-1520_Ver1_5.xml
    CPS_E5DC_Ver0_0.xml
Improved functions
  • Solved the problem that the local network may be assigned to the peripheral port when it is added to Unit 0 Port 1 in the PLC routing table.
  • Solved the problem that Differential Monitor executions may fail in NS-Thru and NV-Thru.

- :CX-One Version 4 Auto-update (February 2013)

New functions

[CPS]

  • Added the following files.
    CPS_NJ301-1100_Ver1_4.xml
    CPS_NJ301-1200_Ver1_4.xml
    CPS_NJ501-1300_Ver1_4.xml
    CPS_NJ501-1400_Ver1_4.xml
    CPS_NJ501-1500_Ver1_4.xml
    CPS_NJ501-4300_Ver1_4.xml
    CPS_NJ501-4310_Ver1_4.xml
    CPS_NJ501-4400_Ver1_4.xml
    CPS_NJ501-4500_Ver1_4.xml
Improved functions

[CPS]

  • Updated the following files.
    CPS_CJ1W-SCU22_Ver2_0.xml
    CPS_CJ1W-SCU22_Ver2_1.xml
    CPS_CJ1W-SCU32_Ver2_0.xml
    CPS_CJ1W-SCU32_Ver2_1.xml
    CPS_CJ1W-SCU42_Ver2_0.xml
    CPS_CJ1W-SCU42_Ver2_1.xml
  • Solved the problem that transferring the data to Position Control Unit fails if G5-series Servo Drive (Linear Motor Type) is in the EtherCAT network.
  • Revised the PLC Connection Cable Selection Guide.

- :CX-One Version 4 Auto-update (November 2012)

New functions

[CX-Server]

  • Supported the CP1E-E60 CPU Units.
    Supported the CP1E-E60SDR-A.
Improved functions
  • Solved the problem that protocol macro may not be backed up by PLC Backup Tool.

- :CX-One Version 4 Auto-update (September 2012)

New functions

[CPS]

  • Added the following files.
    CPS_CJ2B-EIP21_Ver2_1.xml
    CPS_CS1W-EIP21_Ver2_1.xml

- :CX-One Version 4 Auto-update (August 2012)

New functions

[CPS]

  • Added the following files.
    CPS_CJ1W-SCU22_Ver2_1.xml
    CPS_CJ1W-SCU32_Ver2_1.xml
    CPS_CJ1W-SCU42_Ver2_1.xml
Improved functions

[CX-Server]

  • Solved the problem that online connection through EtherNet/IP may fail when a specific text string is used for device name of network card.
  • Solved the problem that cannot edit the data link settings for model NS-CLK21.
  • Solved the problem that fails to backup CJ2H Unit Ver.1.1 Built-in EIP Unit in PLC Backup tool.

- :CX-One Version 4 Auto-update (April 2012)

New functions

[CPS]

  • Added the following files.
    CPS_CP1L-EL20DR-D_Ver1_0.xml
    CPS_CP1L-EL20DT1-D_Ver1_0.xml
    CPS_CP1L-EL20DT-D_Ver1_0.xml
    CPS_CP1L-EM30DR-D_Ver1_0.xml
    CPS_CP1L-EM30DT1-D_Ver1_0.xml
    CPS_CP1L-EM30DT-D_Ver1_0.xml
    CPS_CP1L-EM40DR-D_Ver1_0.xml
    CPS_CP1L-EM40DT1-D_Ver1_0.xml
    CPS_CP1L-EM40DT-D_Ver1_0.xml
    CPS_CP1L-ETN21_Ver0_0.xml
    CPS_CP1L-ETN21_Ver1_0.xml

[CX-Server]

  • Supported the CP1L-EL / -EM CPU Units.
    Supported the models CP1L-EL[][][][]-[] and CP1L-EM[][][][]-[].

[NewNCF]

  • Supported G5-series Servo Drive (with Built-in EtherCAT Communications Linear Motor Type) Ver1.1 to be released soon.
  • Supported 3G3RX-series Inverter to be released soon.
Improved functions

[CPS]

  • Updated the following files.
    CPS_CJ1W-OD233_Ver0_0.xml
    CPS_CJ1W-CT021_Ver0_0.xml
    CPS_CJ1W-CT021_Ver1_0.xml
    CPS_CS1W-CT021_Ver0_0.xml
    CPS_CS1W-CT041_Ver0_0.xml

[CX-Server]

  • Supported making the response timeout setting when CJ2-series select USB or EtherNet/IP for the Network Type.
  • Solved the problem that the Change PLC dialog may not be displayed in the case of connection via a gateway PLC.

- :CX-One Version 4 Auto-update (February 2012)

New functions

[CPS]

  • Added the following file.
    CPS_CJ1W-EIP21_Ver2_1.xml
Improved functions
  • Solved the problem that prevented normal calculation of current and width on I/O table of Position Control Unit (CJ1W-NC[]81 and CJ1W-NC[]82).
  • Solved the problem that prevented normal display of velocity on Memory Operation Preview if the Axis Type is Unlimited Axis(Rotation Axis).
  • Solved the problem that prevented normal display of acceleration time on Memory Operation Preview when you operate interpolation with Memory Operation.

- :CX-One Version 4 Auto-update (November 2011)

New functions

[CPS]

  • Added the following files.
    CPS_E5CC_Ver0_0.xml
    CPS_E5EC_Ver0_0.xml
Improved functions
  • Solved the problem that the Command Pulse Count Per Motor Rotation and the Work Travel Distance per Motor Rotation were not calculated correctly in the electronic gear setting function.
  • Improved the CX-One AutoUpdate Tool so that it can be used commonly with other Omron Tools.
  • Solved the problem that GRT1-CRT SmartSlice I/O is not displayed in the component list of CX-Integrator.

- :CX-One Version 4 Auto-update (August 2011)

Improved functions

[CPS]

  • Added the following files.
    CPS_CJ1W-PNT21_Ver0_0.xml
    CPS_CS1W-PNT21_Ver0_0.xml
    CPS_CJ1W-SCU21-V1_Ver1_3.xml
    CPS_CJ1W-SCU22_Ver2_0.xml
    CPS_CJ1W-SCU31-V1_Ver1_3.xml
    CPS_CJ1W-SCU32_Ver2_0.xml
    CPS_CJ1W-SCU41-V1_Ver1_3.xml
    CPS_CJ1W-SCU42_Ver2_0.xml
    CPS_CS1W-SCB21-V1_Ver1_3.xml
    CPS_CS1W-SCB41-V1_Ver1_3.xml
    CPS_CS1W-SCU21-V1_Ver1_3.xml
    CPS_CS1W-SCU31-V1_Ver1_3.xml

    Improved the setting component for Position Control Units (CJ1W-NC[]81 and CJ1W-NC[]82) in the following point:
  • Solved the problem which caused communications errors at startup on rare occasions.

- :CX-One Version 4 Auto-update (May 2011)

New functions

[CPS]

  • Added the following files.
    CPS_CJ1W-NC281_Ver1_3.xml
    CPS_CJ1W-NC481_Ver1_3.xml
    CPS_CJ1W-NC881_Ver1_3.xml
    CPS_CJ1W-NCF81_Ver1_3.xml
    CPS_CJ1W-NC482_Ver1_3.xml
    CPS_CJ1W-NC882_Ver1_3.xml
    CPS_CJ1W-NCF82_Ver1_3.xml

[Support of New Types]

  • Supported the Position Control Units with EtherCAT communications (models CJ1W-NC281, 481, 881, F81, 482, 882, and F82 in Ver.1.3).

    Added the following functions to setting component for Position Control Units (models CJ1W-NC[]81and []82).
  • Parameters and memory operation sequence data can be imported and exported in csv format.
  • Operations with memory operation sequence data can be undone and redone.
  • Lines can be added to or deleted from memory operation sequence data.
  • Pulse rate setting can be automatically calculated from machine configuration information.

    Added the following functions to setting component for Position Control Units (models CJ1W-NC[][]4).
  • Range check determined by axis parameters can be reflected to memory operation sequence data.
  • Parameters and memory operation sequence data can be imported and exported in csv format.
  • Operations with memory operation sequence data can be undone and redone.
  • Lines can be added to or deleted from memory operation sequence data.
Improved functions
  • Can write into PLC system setting area (DM6144 to DM6655) of IDSC from PLC memory.

- :CX-One Version 4 Auto-update (January 2011)

New functions
  • Added the PLC connection cable selection guide to the shortcut menu introduction guide library.
  • CPU Bus Units can be registered as synchronization control target Units.

[CX-Server]

  • Supported the CJ2H Ver.1.4 CPU Unit.

[CPS]

  • Added the following files.
    CPS_CJ2H-CPU64_Ver1_4.xml
    CPS_CJ2H-CPU65_Ver1_4.xml
    CPS_CJ2H-CPU66_Ver1_4.xml
    CPS_CJ2H-CPU67_Ver1_4.xml
    CPS_CJ2H-CPU68_Ver1_4.xml
    CPS_CJ2H-CPU64-EIP_Ver1_4.xml
    CPS_CJ2H-CPU65-EIP_Ver1_4.xml
    CPS_CJ2H-CPU66-EIP_Ver1_4.xml
    CPS_CJ2H-CPU67-EIP_Ver1_4.xml
    CPS_CJ2H-CPU68-EIP_Ver1_4.xml
Improved functions
  • Solved the problem about transferring Unit setting. With the Windows Vista or Windows 7 to which MS Office2010 is installed, the Unit setting information of a part of Units could not be transferred.

- :CX-One Version 4 Auto-update (October 2010)

New functions
  • Can reflect the range check in accordance with the Axis Parameter setting to Memory Operation Sequence Data on Position Control Unit (CJ1W-NC[]81 and CJ1W-NC[]82) Setting Component.

[CPS]

  • Added the following file:
    CPS_CJ2M-EIP21_Ver2_1.xml

[Support of New Types]

  • Supported the built-in EIP Unit version 2.1 of CJ2M-CPU3[].
  • Supported the G5-series Servo Drive (EtherCAT communication type R88D-KN[]-ECT (the model without "-R")) which would be released shortly. On Position Control Unit (CJ1W-NC[]81 and CJ1W-NC[]82) Setting Component, the model R88D-KN[]-ECT-R is described as Ver.1.0 while the model R88D-KN[]-ECT (the model without "-R") as Ver.2.0.
Improved functions
  • Solved the problem that disturbed error occurrence even if a Unit total power consumption exceeded the allowable consumption for a power supply.(CS/CJ PLC)
  • Can transfer projects created by a previous version of Position Control Unit (CJ1W-NC[]81 and CJ1W-NC[]82) Setting Component on the new version, which was previously impossible.
  • Solved the problem that the Axis Parameter editing screen could not start up when an out-of-range Axis Parameter was set on Position Control Unit (CJ1W-NC[]81 and CJ1W-NC[]82) Setting Component.
  • Solved the problem that the Axis Parameter editing screen could not start up when an out-of-range Axis Parameter was set on Position Control Unit (CJ1W-NC[][]4) Setting Component
    .

[CX-Server]

  • Enhanced the recovery function from communications errors at USB connection.

- :CX-One Version 4 Auto-update (July 2010)

New functions

[CPS]

  • Added the following files:
    CPS_CJ1W-NC214_Ver1_1.xml
    CPS_CJ1W-NC234_Ver1_1.xml
    CPS_CJ1W-NC414_Ver1_1.xml
    CPS_CJ1W-NC434_Ver1_1.xml
    CPS_CJ1W-NC281_Ver1_1.xml
    CPS_CJ1W-NC481_Ver1_1.xml
    CPS_CJ1W-NC881_Ver1_1.xml
    CPS_CJ1W-NCF81_Ver1_1.xml
    CPS_CJ1W-NC482_Ver1_1.xml
    CPS_CJ1W-NC882_Ver1_1.xml
    CPS_CJ2M-CPU11_Ver2_0.xml
    CPS_CJ2M-CPU12_Ver2_0.xml
    CPS_CJ2M-CPU13_Ver2_0.xml
    CPS_CJ2M-CPU14_Ver2_0.xml
    CPS_CJ2M-CPU15_Ver2_0.xml
    CPS_CJ2M-CPU31_Ver2_0.xml
    CPS_CJ2M-CPU32_Ver2_0.xml
    CPS_CJ2M-CPU33_Ver2_0.xml
    CPS_CJ2M-CPU34_Ver2_0.xml
    CPS_CJ2M-CPU35_Ver2_0.xml
    CPS_NSJ5-SQ00_Ver6_7.xml to Ver8_2.xml
    CPS_NSJ5-SQ01_Ver6_7.xml to Ver8_2.xml
    CPS_NSJ5-SQ10_Ver8_1.xml to Ver8_2.xml
    CPS_NSJ5-SQ11_Ver8_1.xml to Ver8_2.xml
    CPS_NSJ5-TQ00_Ver6_7.xml to Ver8_2.xml
    CPS_NSJ5-TQ01_Ver6_7.xml to Ver8_2.xml
    CPS_NSJ5-TQ10_Ver8_1.xml to Ver8_2.xml
    CPS_NSJ5-TQ11_Ver8_1.xml to Ver8_2.xml
    CPS_NSJ8-TV00_Ver6_7.xml to Ver8_2.xml
    CPS_NSJ8-TV01_Ver6_7.xml to Ver8_2.xml
    CPS_NSJ10-TV00_Ver6_7.xml to Ver8_2.xml
    CPS_NSJ10-TV01_Ver6_7.xml to Ver8_2.xml
    CPS_NSJ12-TS00_Ver6_7.xml to Ver8_2.xml
    CPS_NSJ12-TS01_Ver6_7.xml to Ver8_2.xml
    CPS_CJ1W-V680C11_Ver1_2.xml
    CPS_CJ1W-V680C12_Ver1_2.xml
    CPS_CS1W-V680C11_Ver1_2.xml
    CPS_CS1W-V680C12_Ver1_2.xml

[Support of New Types]

  • Supported Position Control Units.
     Supported models CJ1W-NC214, -NC234, -NC414, and -NC434 Ver.1.1.
  • Supported Position Control Units with EtherCAT interface.
     Supported models CJ1W-NC281, -NC481, NC881, -NCF81,
    -NC482, and -NC882 Ver.1.1.

[CX-Server]

  • Supported Ethernet communications to CP1E-series PLCs by using CP1W-CIF41 Option Boards.
  • Supported CJ2M Ver.2.0 CPU Units.

[CX-One Information]

Added an application to the start menu to confirm version information.

- :CX-One Version 4 Auto-update (April 2010)

New functions

[Support of New Types]

  • Supported Position Control Units with EtherCAT interface.
    Supported models CJ1W-NC281, -NC481, and -NC881.

[CPS]

  • Added the following files
    CPS_CJ1W-NC281_Ver1_0.xml
    CPS_CJ1W-NC481_Ver1_0.xml
    CPS_CJ1W-NC881_Ver1_0.xml
Improved functions
  • Solved the problem of the inconsistencies in display order and expression between the project tree and the transfer/verification screens of the Position Control Unit (CJ1W-NC[][]4) Setting Component.
  • Solved the problem of the setting for the Axis Type parameter on Position Control Unit(CJ1W-NC[][]4) Setting Component, to prevent any setting other than the specified range.

- :CX-One Version 4 Auto-update (February 2010)

New functions

[CPS]

  • Added the following files
    CPS_CJ2M-CPU11_Ver1_0.xml
    CPS_CJ2M-CPU12_Ver1_0.xml
    CPS_CJ2M-CPU13_Ver1_0.xml
    CPS_CJ2M-CPU14_Ver1_0.xml
    CPS_CJ2M-CPU15_Ver1_0.xml
    CPS_CJ2M-CPU31_Ver1_0.xml
    CPS_CJ2M-CPU32_Ver1_0.xml
    CPS_CJ2M-CPU33_Ver1_0.xml
    CPS_CJ2M-CPU34_Ver1_0.xml
    CPS_CJ2M-CPU35_Ver1_0.xml
    CPS_CJ2M-EIP21_Ver2_0.xml
    CPS_CJ2H-CPU64_Ver1_3.xml
    CPS_CJ2H-CPU64-EIP_Ver1_3.xml
    CPS_CJ2H-CPU65_Ver1_3.xml
    CPS_CJ2H-CPU65-EIP_Ver1_3.xml
    CPS_CJ2H-CPU66_Ver1_3.xml
    CPS_CJ2H-CPU66-EIP_Ver1_3.xml
    CPS_CJ2H-CPU67_Ver1_3.xml
    CPS_CJ2H-CPU67-EIP_Ver1_3.xml
    CPS_CJ2H-CPU68_Ver1_3.xml
    CPS_CJ2H-CPU68-EIP_Ver1_3.xml

[CX-Server]

  • Supports CP1E CPU Units.
    Supports models CP1E-E10, -E14, -N14, and -N60.
  • Supports CJ2M CPU Units.
    Supports models CJ2M-CPU[][].
  • Supports CJ2H Ver.1.3 CPU Units.
  • Can connect to CP1E-series CPU Units via SYSWAY.
Improved functions
  • Changed and improved a unit in PCU (CJ1W-NC[][]4) parameter setting. The unit of Work Travel Distance per Monitor Rotation for Axis Parameter was changed to Display Unit.
  • Unified and improved a unit in PCU (CJ1W-NC[][]4) parameter setting. The set value displays for Axis Parameter and Task Parameter were unified into the minimum setting unit (Command Unit).
  • Solved the problem in PCU (CJ1W-NC[][]4) Memory Operation Preview. The value displayed by the Preview did not update the setting made by Unit multiplier of Axis Parameter.

- :Version V4.* → CX-One Version 4 Auto-update (December 2009)

Improved functions

[CX-Server]

  • Can connect to CJ2H CPU Units via SYSWAY.

- :Version V4.* → CX-One Version 4 Auto-update (October 2009)

New functions

[CPS]

  • Added the following files
    CPS_CJ1W-SCU22_Ver2_0.xml
    CPS_CJ1W-SCU32_Ver2_0.xml
    CPS_CJ1W-SCU42_Ver2_0.xml
    CPS_NS15-TX01-V2.xml
    CPS_CJ2H-CPU64_Ver1_2.xml
    CPS_CJ2H-CPU64-EIP_Ver1_2.xml
    CPS_CJ2H-CPU65_Ver1_2.xml
    CPS_CJ2H-CPU65-EIP_Ver1_2.xml
    CPS_CJ2H-CPU66_Ver1_2.xml
    CPS_CJ2H-CPU66-EIP_Ver1_2.xml
    CPS_CJ2H-CPU67_Ver1_2.xml
    CPS_CJ2H-CPU67-EIP_Ver1_2.xml
    CPS_CJ2H-CPU68_Ver1_2.xml
    CPS_CJ2H-CPU68-EIP_Ver1_2.xml
Improved functions
  • Solved the problem of incorrect indication. When the Routing Table Component of the CX-Integrator was started up from the I/O table while the CJ1W-PH41U was mounted, the indication told it was "Ethernet".

[CX-Server]

  • Improved the communication performance with DeviceNet Units that use USB-connected PLC as gateway.
  • Solved the problem of unstable operation. The problem occurred when the PC that had no serial port or modem port was used to operate the C/CV-series PLC.

- :Version V4.* → CX-One Version 4 Auto-update (August 2009)

New functions

[CPS]

  • Added the following files
    CPS_E5GN_Ver0_0.xml
Improved functions
  • Fixed the comments that are displayed in the I/O table of CJ(S) 1W-CRM21.

Change history of CX-Programmer

Ver.9.51 : CX-One Version 4 Auto-update (January 2014)

Improved functions
  • Improved so that you can narrow down the Controller models on a series-by-series basis when selecting the Controller to connect in the auto online connection (direct connection).
  • Improved so that you can select not to display the information window from the next time.

Ver.9.50 : CX-One Version 4 Auto-update (September 2013)

Improved functions
  • Solved the problem that array index variables may be changed to 0 by a Compare with PLC operation when they are used in a structure array variable specified as a network variable.
  • Solved the problem that condition flags are changed to wrong Input Comparison Instructions when changing the PLC from CV series to CS/CJ series.
  • Solved the problem that the same memory may be allocated to a STRING variable and other auto-allocated variable if auto memory allocation is specified for the STRING variable.
  • Solved the problem that program check may detect an error when a stack operation is specified for DISTC or COLL instruction.

Ver.9.44 : CX-One Version 4 Auto-update (June 2013)

Improved functions
  • Solved the problem that cross reference may not be printed correctly for the programs in Cyclic Task 32 or later.
  • Solved the program that CX-Programmer may not respond when pop-up menu is displayed for an FB instance in the variable table for an ST function block.
  • Solved the problem that index may change to 0 in the program comparison when a structure array variable that is specified as a network variable is used in an array index.
  • Solved the problem that CX-Programmer may be shut down when the Search, Replace, or Change All operation is performed for the variable table immediately after the I/O Comment dialog box or Cross-Reference Report dialog box is closed.
  • Solved the program that CX-Programmer may not respond when executing the Model Conversion operation for a program with an annotation or rung comment that ends in the text string ";\".
  • Solved the problem that CX-Programmer may be shut down when editing a specific symbol by Smart Input Mode in FB Ladder.
  • Solved the problem that File Conversion Utility cannot import the data correctly if a file name includes any spaces in the LSS data file.
  • Solved the problem that program check detects an error when using an AVG instruction in block programs.

Ver.9.43 : CX-One Version 4 Auto-update (February 2013)

Improved functions
  • Solved the problem that constant operands of MOVB/BCNT/COLL/DIST/XFER instructions are not converted correctly.
  • Solved the problem that online connection can be made to other PLC models via an ETN Unit using the CP1L-Ethernet connection.
  • Solved the problem that CX-Programmer may be shut down when a special instruction with an empty operand is edited in Smart Input mode.
  • Solved the problem that CX-Programmer may be shut down when you set the FB/SFC memory range if the FB/SFC stack setting is changed from the default value.

Ver.9.42 : CX-One Version 4 Auto-update (November 2012)

New functions
  • Supported the CP1E-E60 CPU Units.
    Supported the CP1E-E60SDR-A.
Improved functions
  • Improved the problem that it takes a long time to insert/delete rows or columns in rungs during Online Editing.
  • Solved the problem that Function Block call instruction disappears when device model is changed to CP1L-L or CP1L-L10.
  • Solved the problem that program cannot be restored correctly when transferred from PLC if a symbol is used for a subscript of an auto-allocated TIMER/COUNTER array in an operand.

Ver.9.41 : CX-One Version 4 Auto-update (August 2012)

New functions
  • Added [Help | Manual] menu for opening the Operation Manuals.
  • Added the new tab in the Output Window for displaying only the compile errors at Compile All PLC Programs.
  • Added a function to compare the auto-allocated symbols
    by symbol name at Compare Program.
Improved functions
  • Solved the problem that takes a long time to upload the program with Network Symbols.
  • Solved the problem that the current focus is moved when using the scroll bar in I/O Comment Window or Cross-Reference Report Window.

Ver.9.40 : CX-One Version 4 Auto-update (April 2012)

New functions
  • Supported the CP1L-EL / -EM CPU Units.
    Supported the models CP1L-EL[][][][]-[] and CP1L-EM[][][][]-[].
Improved functions
  • Solved the problem that caused an application error when operands which can be used only in NUMBER data type displayed in mnemonic were replaced or changed all.
  • Solved the problem that data cannot be transferred correctly when a rung with line comment and a section with the null last line is deleted by Online Editing.

Ver.9.35 : CX-One Version 4 Auto-update (February 2012)

Improved functions
  • Solved the problem that prevented operating properties displayed when adding a section on Section/Rung Manager.
  • Solved the application error that occurred when an array member of AT specification structure array with a subscript symbol is used in an instruction of FB ladder program.
  • Solved the problem that prevented normal operation of programs which used subscript symbols in AT specification structure arrays.
  • Improved the process time of [Function Block / SPC Memory Statistics] in programs having structures.
  • Improved the error messages shown when you changed set values of binary type timer / counter instructions while CX-Simulator is connected.
  • Corrected the different description of C-series PMCR instruction operand names from those on PLC manual.
  • Solved the problem that prevented correct restoration of programs which used subscript variables in auto-allocated structure arrays when to Transfer [PLC to PC].

Ver.9.34 : CX-One Version 4 Auto-update (November 2011)

Improved functions
  • Improved the time taken to complete displaying the UM memory while structures were used in function blocks.
  • Improved the time taken to decompile a program which has function blocks and structures when it was transferred from PLC to PC.
  • Improved the time taken to complete changing models for programs in which function blocks and structures were used.
  • Solved the problem that some models selected on the PLC Model Selection dialog box to add new PLCs prevented displaying the I/O table.
  • Solved the problem that CX-Programmer ended abnormally when a rung header area was selected on a section view while the property dialog box was open.
  • Corrected the misdescription about the shortcut key reference.
  • Solved the problem that structure symbols were deleted along with deletion of unused symbols.

Ver.9.33 : CX-One Version 4 Auto-update (August 2011)

Improved functions
  • Solved the problem that displayed the wrong number of used words when a STRING symbol was specified to a FB parameter in a ladder section.
  • Solved the problem that prevented using 17 or greater bit sizes for the third operand when a structure symbol was specified for the first operand of the SETA/RSTA instruction.
  • Solved the problem that caused an application error when data was added to a null line whose immediate above was a structure member of a FB input-output symbol.
  • Solved the problem which prevented specifying a structure member of a subscript symbol to a FB input-output parameter in a task ST.
  • Solved the problem that made the address offset operand of a subscript address an illegal operand after a model conversion and transfer from PLC to PC.
  • Solved the problem that displayed CIO comments as I/O comments when a timer/counter number was entered to the first operand of a Timer/Counter instruction.
  • Improved the time required to copy and paste variables
    including array symbols from Excel to Symbol table.

Ver.9.32 : CX-One Version 4 Auto-update (May 2011)

New functions
  • Instructions in Smart Input Mode only can be edited.
Improved functions
  • Improved the period to save project files whose FBs are protected, into network drives.
  • Solved the problem that caused abnormal shutdown when an unused symbol was deleted.
  • Solved a problem with conduction state display. When an operand of a special instruction for output bits is an input or output symbol, the conduction state display does not become active even if the present value of operand address is true.
  • Solved the problem about the setting change. While the E10 or subsequent bank is used for FB/SFC memory allocation address, loading a project file changed the setting to the default.

Ver.9.31 : CX-One Version 4 Auto-update (Feburary 2011)

Improved functions
  • Solved the problem that caused a compile error on a program which used a line comment or remark.

Ver.9.30 : CX-One Version 4 Auto-update (January 2011)

New functions

[Support of New Types]

  • Supported the CJ2H Ver.1.4 CPU Units.
  • On the ST Editor View, you can specify a line number to jump to.
  • From the list, you can select and enter functions and symbols that have been registered..
  • You can confirm a ST syntax error when it is entered.
  • On the FB Ladder View, you can enter in the SMART INPUT mode.
  • A popup menu was added to introduce a structure member as the last structure member.
Improved functions
  • Solved the problem regarding address offset. Even if an address offset had an illegal data, it did not become an error. But it was transferred to PLC.
  • Solved the problem regarding program display. If an address of AT specified FB symbol was the same as an address of a global symbol, a program transferred from PLC->PC was not properly displayed.
  • Solved the problem that the size of Line Comment Jump dialog box could not be changed on the Function Ladder View.
  • Solved the problem that the information of the Cross Reference popup menu was not updated when the cursor was moved by the arrow keys over the function block symbol table.
  • Solved the problem that input strings could not be read while input and output symbols of FB were ON.
  • Solved the problem regarding CMP(020) instruction. When a reusable file which had CMP(020) instruction was added to a project, it turned to be an error.
  • Can connect with CP1E-N[][] on PLC-PT Integrated Simulation.

Ver.9.21 : CX-One Version 4 Auto-update (November 2010)

Improved functions
  • Solved the problem of rung error caused by automatic insertion of vertical connecting line. The error occurred when an instruction was added while the option to validate inserting of connecting line is available.
  • Solved the problem which prevented opening a project file. When a project file to which automatic memory allocation was set was saved by CX-Programmer V9.20, it cannot be opened by V9.12 or earlier versions.

Ver.9.20 : CX-One Version 4 Auto-update (October 2010)

New functions
  • Can use structure symbols in ST.
  • Can use timer and counter symbols in ST.
  • Can use the following ten functions in ST:
    MOD (remainder), SHL (left bit shift), SHR (right bit shift), ROL (left bit rotation), ROR (right bit rotation), LIMIT (upper and lower limit control), SEL (data selection), MUX (data extraction), MAX (max search) and MIN (min search).
  • Can copy and paste structure symbols to CX-Designer (V3.20 and higher). (CJ2 PLC)
Improved functions
  • Solved the problem that prevented cursor movement after using the F3 key for continuous searches.
  • Solved the problem that caused a program error on PLC when the SETB instruction was used in FB ladder program and the program was transferred to PLC.
  • Solved the problem that caused GPF at existing CX-Programmer when a project to which automatic memmory allocation was set.

Ver.9.12 : CX-One Version 4 Auto-update (July 2010)

New functions

[Support of New Types]

  • Supported CJ2M Ver.2.0 CPU Units.
  • Supported CJ2M Pulse I/O Modules.
    Supported CJ2M-MD211 and -MD212.
  • Supported Ethernet communications to CP1E-series PLCs by using CP1W-CIF41 Option Boards.
Improved functions
  • Solved the problem that an error occurred at loading files if a SFC STEP flag (.x) was used as the FB input parameter.
  • Solved the problem that the Address Offset operand was not properly updated when the Transfer [PC -> PLC] was executed after a model conversion.
  • Solved the problem that an application error occurred when a structure symbol was selected on the ladder view and copied and pasted to the Watch Window.

Ver.9.11 : CX-One Version 4 Auto-update (April 2010)

Improved functions
  • Enabled to select the function to insert a null line under the selected rung automatically.
  • Enabled to select the function to insert a connecting line automatically when an instruction is added or deleted.
  • Solved the problem that the rung data having the DIFU/DIFD instructions did not show on the Address Reference Tool window.
  • Solved the problem of jumping from the Address Reference Tool window to one line under the target.
  • Solved the problem that a ladder having a linefeed code in an I/O comment could not be printed by layout printing on a CJ2-series Unit.
  • Solved the problem that the timer did not show on the Detailed usage, when you specified it by its number in the NUMBER data type.

Ver.9.10 : CX-One Version 4 Auto-update (February 2010)

New functions
  • Can connect to CP1E-series CPU Units via SYSWAY.

[Support of New Models]

  • Supports CP1E CPU Units.
    Supports models CP1E-E10, -E14, -N14, and -N60.
  • Supports CJ2M CPU Units.
    Supports models CJ2M-CPU[][].
  • Supports CJ2H Ver.1.3 CPU Units.
Improved functions
  • Can display structure array symbols as candidate operands for ladder instructions.
  • Solved the problem that counter and timer comments of CP1E ladder programs. were not printed.
  • Solved the problem in function block arguments. Proper execution was sometimes prevented when an arithmetic expression was used in a function block argument within a ST task.
  • Solved the problem that I/O comments might be deleted if the addresses before and after a replacement overlapped in Replace or Change All.
  • Solved the problem in Replace. When the software was first stared up after upgrading, replacements might fail even the target options were properly selected.

Ver.9.04 : Version V4.* → CX-One Version 4 Auto-update (December 2009)

New functions
  • Configuration software for CJ1W-NC[][]4 PCU Unit has the function to preview the memory operation data.
  • Can connect to CJ2H CPU Units via SYSWAY.

[Support of New Types]

  • Supports CP1E CPU Units.
    Supports model CP1E-NA.

[Enhanced Function by Smart Input Mode]

  • Can finalize all entries by pressing Shift and Enter keys together.
  • Can enter the same instruction consecutively by pressing Ctrl and Enter keys together.
  • Can show the address increment candidates for each area type.
  • Can analyze the operand data of instruction that is used in plural locations of a single circuit, and show the candidates.
  • Up and down arrow keys can increment and decrement address values that are specified by instruction operands.
Improved functions
  • Solved the problem in CJ1W-ETN21 and CS1W-ETN21 CPU Bus Units that could not properly show and verify the parameters.
  • Improved the function that trace result graphs can be zoomed in and out in Data Trace Function.
  • Solved the problem that could not print the title column with Windows Vista.
  • Solved the problem that FB might be changed into another instance by program downloading, when CIO array symbols are used.

Ver.9.02 : Version V4.* → CX-One Version 4 Auto-update (August 2009)

Improved functions
  • Imporved the performance in time required to have the Auto Online Connection to the NV-series host PLC.

Change history of CX-Integrator

Ver.2.59 : CX-One Version 4 Auto-update (January 2014)

Improved functions
  • Solved the problem that error logs of CS1W-DRM21-V1 were not displayed correctly.
  • Corrected the terms on the DeviceNet parameter edit view.

Ver.2.58 : CX-One Version 4 Auto-update (June 2013)

New functions
  • Supported the KE1-DRT-FLK Smart Monitoring Device DeviceNet Communication Unit.
Improved functions
  • Solved the problem that "Designation of 62 nodes" is not displayed for ***_CLK23 Controller Link Units in the diagnosis of settings by the Controller Link Network Diagnostic Tool.

Ver.2.57 : CX-One Version 4 Auto-update (February 2013)

Improved functions
  • Improved the link-off problem in the help file.

Ver.2.56 : CX-One Version 4 Auto-update (November 2012)

Improved functions
  • Solved the problem that GRT1-DRT(DeviceNet) does not work on Windows 7 or Vista.

Ver.2.55 : CX-One Version 4 Auto-update (August 2012)

New functions
  • Supported the DeviceNet communication unit for RX series inverter : Model 3G3AX-RX-DRT-E.

Ver.2.53 : CX-One Version 4 Auto-update (April 2012)

Improved functions
  • Supported the CP1L-EL / -EM CPU Units.
    Supported the models CP1L-EL[][][][]-[] and CP1L-EM[][][][]-[].

Ver.2.52 : CX-One Version 4 Auto-update (February 2012)

Improved functions
  • Solved the problem that writing of serial No. is not sometimes finished on WD30-ME-V1.

Ver.2.51 : CX-One Version 4 Auto-update (November 2011)

New functions
  • Supported the CompoNet communication unit for MX2 series inverter : Model 3G3AX-MX2-CRT-E
Improved functions
  • Improved the Warning message on unsupported devices.

Ver.2.50 : CX-One Version 4 Auto-update (August 2011)

Improved functions
  • Improved the description of Auto Online Dialogue Box.

Ver.2.44 : CX-One Version 4 Auto-update (May 2011)

New functions

[Support of New Type]

  • Supported the Model R88A-NCW152-DRT CIP Revision 2.x devices.

Ver.2.43 : CX-One Version 4 Auto-update (October 2010)

Improved functions
  • Updated the device vender name displayed in the DeviceNet Component list.

Ver.2.42 : CX-One Version 4 Auto-update (February 2010)

New functions

[Support of New Models]

  • Supports CJ2M CPU Units.
    Supports models CJ2M-CPU[][].

Ver.2.41 : Version V4.* → CX-One Version 4 Auto-update (October 2009)

Improved functions
  • Solved the problem that you can not start CX-Integrator when the latest version of CX-ConfiguratorFDT is installed .

Change history of CX-Protocol

Ver.1.97 : CX-One Version 4 Auto-update (February 2013)

Improved functions
  • Improved the link-off problem in the help file.

Ver.1.96 : CX-One Version 4 Auto-update (August 2012)

New functions
  • Supported the models CJ1W-SCU22, -SCU32 and -SCU42 Unit Ver.2.1.

Ver.1.95 : CX-One Version 4 Auto-update (February 2012)

Improved functions
  • Revised the operation manual.

Ver.1.94 : CX-One Version 4 Auto-update (November 2011)

Improved functions
  • Improved the problem that in some installation conditions unnecessary messages were shown at startup.

Ver.1.93 : CX-One Version 4 Auto-update (August 2011)

Improved functions
  • Improved the link-off problem in the help file.

Ver.1.92 : CX-One Version 4 Auto-update (February 2010)

New functions

[Support of New Models]

  • Supports CJ2M CPU Units.
    Supports models CJ2M-CPU[][].

Change history of CX-Simulator

Ver.1.994 : CX-One Version 4 Auto-update (September 2013)

Improved functions
  • Solved the problem that the Simulator cannot connect with a CP1E-NA.

Ver.1.993 : CX-One Version 4 Auto-update (November 2012)

New functions
  • Supported the CP1E-E60 CPU Units.
    Supported the CP1E-E60SDR-A.

Ver.1.992 : CX-One Version 4 Auto-update (August 2012)

Improved functions
  • Solved the problem that DMPX Instruction may be executed in spite of an error flag is ON.

Ver.1.991 : CX-One Version 4 Auto-update (April 2012)

Improved functions
  • Supported the CP1L-EL / -EM CPU Units.
    Supported the models CP1L-EL[][][][]-[] and CP1L-EM[][][][]-[].

Ver.1.99 : CX-One Version 4 Auto-update (January 2011)

Improved functions
  • Solved the problem that SFT instruction did not operate properly in a certain address.

Ver.1.98 : CX-One Version 4 Auto-update (October 2010)

Improved functions
  • Solved the problem that could not display present values correctly on a program that uses function block input and output symbols.

Ver.1.97 : CX-One Version 4 Auto-update (July 2010)

New functions

[Support of New Types]

  • Supported CJ2M Ver.2.0 CPU Units.
  • Supported forced sets and resets to EM bit addresses specified by banks, which were used by CJ2H and CJ2M.
Improved functions
  • Solved the problem that the present values of FB symbols whose defaults were set cannot be changed.

Ver.1.96 : CX-One Version 4 Auto-update (April 2010)

Improved functions
  • Solved the problem that the ladders using the function blocks on CJ2M could not be transferred due to the capacity limit.

Ver.1.95 : CX-One Version 4 Auto-update (February 2010)

New functions

[Support of New Models]

  • Supports CJ2M CPU Units.
    Supports models CJ2M-CPU[][].

Ver.1.94 : Version V4.* → CX-One Version 4 Auto-update (December 2009)

New functions

[Support of New Types]

  • Supports CP1E CPU Units.
    Supports models CP1E-NA.

Change history of CX-Motion-NCF

Ver.1.93 : CX-One Version 4 Auto-update (August 2011)

Improved functions
  • Solved the problem that FINS network address and FINS node address are not updated after changing the network type.

Ver.1.92 : CX-One Version 4 Auto-update (July 2010)

Improved functions
  • Improved the displayed servo parameter number and input/output signal setting of G5 series servo drive.

Change history of CX-Motion-MCH

Ver.2.28 : CX-One Version 4 Auto-update (September 2013)

Improved functions
  • Solved the problem that servo parameters are initialized when compared.

Ver.2.27 : CX-One Version 4 Auto-update (June 2013)

Improved functions
  • Solved the program that servo parameter setting values may not be restored correctly when a project file is opened or servo parameters are transferred from an MC Unit or Servo Drive.

Ver.2.26 : CX-One Version 4 Auto-update (November 2012)

Improved functions
  • Solved the problem that the project files created by Japanese-version CX-Motion-MCH may not be retrived by the English-version CX-Motion-MCH.
  • Solved the problem that servo/motor model information may be changed if the project is transferred to MC Unit without servo parameters and then transferred from the MC Unit to the CX-Motion-MCH.

Ver.2.25 : CX-One Version 4 Auto-update (July 2010)

Improved functions
  • Solved the problem that CX-Motion-MCH crashes if multi-byte charactor is in motion programs except comment part.

Change history of CX-Motion

Ver.2.38 : CX-One Version 4 Auto-update (February 2013)

Improved functions
  • Solved the problem that ABS (R88D-G) type cannot be set in Coordinate Parameters.

Ver.2.37 : CX-One Version 4 Auto-update (November 2011)

New functions
  • Improved the function that capital letters in project file name are kept when overwriting the project file.
Improved functions
  • Solved the problem that the setting value is changed when going back from print dialog.

Change history of CX-Drive

Ver.2.93 : CX-One Version 4 Auto-update (January 2014)

Improved functions
  • Added a new function to save all files under a specified name (Save All As).
  • Solve the problem that 32-bit signals are incorrectly rounded down in Data Trace graph for G5-Series.
  • Solve the problem that online connection fails for R88D-WT with firmware version 17 or earlier.

Ver.2.92 : CX-One Version 4 Auto-update (September 2013)

New functions
  • Support High Frequency Mode of inverter MX2-V1 series.

Ver.2.90 : CX-One Version 4 Auto-update (June 2013)

New functions
  • Added the motor types that can be selected in the motor setting function of G5-series Servo Drives (Linear motor type).
Improved functions
  • Solved the problem that parameter transfer fails for G5-series Servo Drives when a negative value is set in the USB connection.
  • Solved the problem that d013 value cannot be displayed correctly for JX-series Inverters.

Ver.2.81 : CX-One Version 4 Auto-update (February 2013)

New functions
  • Supported the MX2-V1 inverters.
  • Supported the Drive Programming function of MX2-V1 inverters.

Ver.2.74 : CX-One Version 4 Auto-update (October 2012)

Improved functions
  • Solved the problem that wrong values may be set for initial values and ranges of parameters which are related to rated current for unit version 1.0 of MX2-series inverters.

Ver.2.72 : CX-One Version 4 Auto-update (August 2012)

New functions
  • Supported the Drive Programming function of RX-V1 inverter.
Improved functions
  • Solved the problem that the cursor value is not displayed when only the vertical axis cursor is read in data tracing and realtime tracing.
  • Solved the problem that the values may be changed after saving and opening data trace results of G5 series.

Ver.2.71 : CX-One Version 4 Auto-update (May 2012)

Improved functions
  • Solved the problem that CX-Drive crashes when opening review file of data trace, real time trace and FFT (extension of the file is *.sdm) if the drive is G5 series with built-in MECHATROLINK-II communication type.
  • Solved the problem that zooming Y-axis of data trace cannot work correctly.

Ver.2.70 : CX-One Version 4 Auto-update (April 2012)

New functions
  • Supported G5-series Servo Drive (with Built-in EtherCAT Communications Linear Motor Type) Ver1.1 to be released soon.
  • Supported 3G3RX-series Inverters (with Built-in EtherCAT Communications Option Boards) to be released soon.
Improved functions
  • Solved the problem that the value of torque demand in real time trace is incorrect if the servo is G5-series with Built-in EtherCAT Communications Type.
  • Solved the problem that the output signals is not displayed correctly in data trace if the servo is is G5-series with Built-in EtherCAT Communications Type.
  • Solved the problem that the unit of acceleration/deceleration time is incorrect for the test run function of G5-series Servo Drives.
  • Solved the problem that SMARTSTEP A-series 100V type is detected as 200V type.
  • Solved the problem that date, time and page number is not printed when printing parameters.

Ver.2.60 : CX-One Version 4 Auto-update (November 2011)

New functions
  • Supported RX inverters 3G3RX-V1 to be released soon.
  • Added easy parameter setup function in G5 servo drives.
  • Added via DeviceNet and via CompoNet connection of MX2 inverters and RX inverters to be released soon.
Improved functions
  • Solved the problem that connecting to drives is failed after conversion to G5 servo drives or MX2 inverters.
  • Solved the problem that default value of G5 series servo drives (R88D-KT) is incorrect.
  • Solved the problem that connecting to drives is failed after opening file if the drive is W series servo drive or SMARTSTEP A series servo drive.

Ver.2.52 : CX-One Version 4 Auto-update (September 2011)

Improved functions
  • Solved the problem that CX-Drive V2.51 automatically transfers electronic gear parameters from servo dirve when go online if the servo is W series(model: R88D-WT) or SMARTSTEP A series(model: R7D-AP).

Ver.2.51 : CX-One Version 4 Auto-update (August 2011)

New functions
  • Added test run function for 3G3MX2 inverter via EtherCAT
Improved functions
  • Solved the problem that text of alarm concurrent bits of R88D-KN-ECT are wrong

Ver.2.40 : CX-One Version 4 Auto-update (May 2011)

New functions

[Support of New Type]

  • Supported the G5-sereis Servo Drive (EtherCAT communication type R88D-KN[]-ECT Ver.2.1) which would be released shortly.
  • Added test run function of MX2 inverter.
  • Added parameter conversion function for
    3G3JV -> 3G3JX
    3G3MV -> 3G3MX2
    R88D-WT -> R88D-KT
    R88D-WT -> R88D-KN
    R88D-WN -> R88D-KN
Improved functions
  • Solved the problem that CX-Drive cannot communicate 3G3RX 3.7kW type.

Ver.2.31 : CX-One Version 4 Auto-update (Feburary 2011)

Improved functions
  • Solved the problem that CX-Drive crashes when closing the review file (file extension: sdm).

Ver.2.30 : CX-One Version 4 Auto-update (January 2011)

New functions
  • Added the damping control function of G5-series servo drives.

Ver.2.20 : CX-One Version 4 Auto-update (October 2010)

New functions

[Support of New Type]

  • Supported the G5-series Servo Drive (EtherCAT communication type R88D-KN[]-ECT (the model without "-R")) which would be released shortly. On CX-Drive, the model R88D-KN[]-ECT-R is described as Ver.1.0 while the model R88D-KN[]-ECT (the model without "-R") as Ver.2.0.
  • Supported 3G3MX2 DeviceNet option board interface(3G3AX-MX2-DRT).
Improved functions
  • Improved the parameter transferring speed for G5 servo driver(R88D-KN[]-ECT Ver.2.0 or later).

Ver.2.10 : CX-One Version 4 Auto-update (July 2010)

New functions

[Support of New Types]

  • Supported the large capacity of G5-series Servo Drive "EtherCAT communication type".
  • Supported 3G3MX2 EtherCAT Option Boards.
    Supported the model 3G3AX-MX2-ECT.
  • Supported the function Autotuning wizard which can make the servo gain tuning easier.

Ver.1.92 : CX-One Version 4 Auto-update (April 2010)

New functions

[Support of New Types]

  • Supported G5-series Servo Drive "EtherCAT communication type".
    Supported models R88D-KN[][][]-ECT-R.

Ver.1.91 : CX-One Version 4 Auto-update (February 2010)

Improved functions
  • Solved the problem that the mistake of displayed data in trigger of data trace window.

Ver.1.91 : Version V4.* → CX-One Version 4 Auto-update (October 2009)

New functions
  • Supports the G5-series Servomotor/Servo Drives with built-in MECHATROLINK-II communications.

Ver.1.90 : Version V4.* → CX-One Version 4 Auto-update (August 2009)

New functions
  • Supporting inverter MX2.
Improved functions
  • Solved the problem that a part of parameters was unable to transfer to the JX/RX-series Inverters.

Change history of CX-Designer

Ver.3.570 : CX-One Version 4 Auto-update (March 2014)

New functions
  • Supported copy and paste functions of Edit Properties.
Improved functions
  • Supported the problem that an error may occur when editing Table component.
  • Supported the problem that a Macro accesses the same address with the original component's address when repeating with offset.
  • Supported the problem that invalid font size may be assigned when font size is modified in a property list.
  • Supported the problem that transferring is unavailable for a part of system version of the NS series.
  • Supported the problem that multitransfer importing does not operate normally.

Ver.3.560 : CX-One Version 4 Auto-update (January 2014)

New functions
  • Supported the Tag replacement in Replacement function.
  • Supported offset processing of structure type array in Repeat function.

Ver.3.550 : CX-One Version 4 Auto-update (September 2013)

New functions
  • Improved that the progress will be displayed when deleting the variables.
  • Supported the function that NS unit displays a warning when the system version other than specified is on the unit during transmitting the project.
  • Improved that focus position will not be moved when the name of the variable is modified in variable table or other.
  • Supported the function that the type String and array can be newly created.
  • Improved that the layout of list edition will be retained.
  • Improved the function that a warning will be skipped to continue transferring data when transferring collectively.
  • Improved that the settings of collective transferring can be done on UI.
  • Improved that the result of transferring will be displayed on UI when transferring collectively.
Improved functions
  • Improved the problem that using a tag for READCMEM in test function intervenes the operating normally.
  • Improved the problem that integrated simulation may not start-up normally in the project using tag.
  • Improved the problem that the settings of the font result in incorrect in the project of multiple labels when the library is reused.

Ver.3.540 : CX-One Version 4 Auto-update (June 2013)

Improved functions
  • Deleted unnecessary settings from Transfer Setting.
  • Supported the function that the user can select the conventional mode when uploading the project.
  • Supported to modify the number of elements in STRING type.
  • Improved the performance during pasting the variables.
  • Solved the problem that a part of the display goes black on Windows 7.
  • Solved the problem that the Alarm/Event Display components are overlapped in test function when the system language is set in the languages other than Japanese or English.
  • Solved the problem that the endian of the text string cannot be the same as the one of NS Unit when the user operates the integrated simulation with NJ.

Ver.3.520 : CX-One Version 4 Auto-update (February 2013)

Improved functions
  • Solved the problem that CX-Designer Introduction Guide had an error in writing.

Ver.3.520 : CX-One Version 4 Auto-update (November 2012)

Improved functions
  • Solved the problem that the device template for E5*C/N may not work properly.
  • Solved the problem that Help had an error in writing.

Ver.3.510 : CX-One Version 4 Auto-update (September 2012)

Improved functions
  • The performance of pasting the variables onto the variables table has been improved.
  • Solved the problem that cannot set the storage format properly on the project V8.5 or later versions when CX-Designer is installed in Chinese (Simplified characters).
  • Solved the problem that the integrated simulation with Sysmac Studio often cannot start up when using the project load macro.
  • Solved the problem that unnecessary line break which occurs when an alarm/event history is saved through the test function.
  • Solved the problem that cannot display the specific character on the keypad through the test function.

Ver.3.500 : CX-One Version 4 Auto-update (August 2012)

Improved functions
  • Added the Palette function.
  • Made an improvement so that the number of array elements can be changed.
  • Added the verification function.
  • Added the batch transfer function.
  • Added the function to have the transfer setting per project.

Ver.3.411 : CX-One Version 4 Auto-update (April 2012)

Improved functions
  • Supported the function to prohibit entering bar codes when the input pad is used.
  • Enhanced checking host names for the line boundary character rules.

Ver.3.40 : CX-One Version 4 Auto-update (February 2012)

New functions
  • Supported the setting that improved the communications performance with Mitsubishi Q/QnA-series PLC.
Improved functions
  • Solved the problem that cleared a part of addresses of Temperature Controller used in project macro.

Ver.3.303 : CX-One Version 4 Auto-update (November 2011)

New functions
  • Supported the function to check inconsistency between macro sources and binary codes.
Improved functions
  • Solved the occasional problem which suspended screen transfer to NS via USB.
  • Solved the problem which prevented rebuilding macro when addresses were replaced from symbol tables while the screen was closed.
  • Solved the problem which caused error ends when a symbol table included unnecessary data.
  • Solved the problem that the default gateway value was also displayed on proxy when the Ethernet setting screen was opened for communications setting.
  • Solved the problem that normal processes were prevented when BCD type was assigned to option values on the pop-up menu for Multifunction objects in the test function.
  • Improved the problem that exiting the communications setting was always slow.

Ver.3.30 : CX-One Version 4 Auto-update (August 2011)

Improved functions
  • Solved the problem where the mouse coordinate display disappeared on Windows 7.
  • Solved the problem where the host name in the macro changed to $W0 when an object to which a macro such as WRITEHOSTB was copied and pasted.

Ver.3.24 : CX-One Version 4 Auto-update (May 2011)

Improved functions
  • Solved the problem that occurred when a password was entered in the Test function on a keypad which was made by a user for password entry.

Ver.3.23 : CX-One Version 4 Auto-update (January 2011)

Improved functions
  • Improved compatibility between RTF files and Microsoft Word files. The RFT files are the ones printed out when the Files are selected as the print output destination.
  • Improved the address replacement performance.
  • Solved the problem which caused abnormal terminations when a validation is executed.
  • Solved the problem about display. When a BMP file was specified to a functional object
  • Solved the problem in reconstruction of DB. The DB was reconstructed every time a project of version7.1 or earlier was opened.
  • Solved the problem in character error. When an indirect reference file was used for a list object, characters turned to be unreadable.
  • Solved the problem in saving. When the character code of a label object was changed on the property list, the change content was not saved.
  • Solved the problem regarding the Word Button upper limit value. When a value over 32768 was set to the upper limit while the Test Function was active, the normal operation was disturbed.

Ver.3.20 : CX-One Version 4 Auto-update (October 2010)

New functions
  • Can copy and paste structure symbols from CX-Programmer (V9.20 and higher). (CJ2 PLC)
Improved functions
  • Solved the problem that prevented transfer of a project whose size is over 20 MB on NS5-[][]1[][]-V2, NSH5-[][][]1[][]-V2 and NSJ5-[][]1[][]-[][][].

Ver.3.12 : CX-One Version 4 Auto-update (July 2010)

Improved functions
  • Improved the function to get the HOSTIDs that are specified by instructions such as READHOSTB more easily.
  • Added the cool parts and backgrounds.

Ver.3.113 : CX-One Version 4 Auto-update (April 2010)

Improved functions
  • Supported importing and exporting all labels at a time.
  • Supported importing and exporting the contents display parts.
  • Improved the display compatibility of Alarm/Event Summary & History objects between CX-Designer and NS.

Ver.3.11 : CX-One Version 4 Auto-update (December 2009)

Improved functions
  • Solved the problem that alarm messages were not properly displayed by the test function.

Ver.3.11 : Version V4.* → CX-One Version 4 Auto-update (October 2009)

Improved functions
  • Enhanced the function to check whether invalid object IDs exist for Validation.
  • Solved the problem that Windows fonts could be specified to reference and show the character string files.

Change history of NV-Designer

Ver.1.190 : CX-One Version 4 Auto-update (June 2013)

Improved functions
  • Solved the problem that the set value of the Valid Condition with Function Switch can be changed when the project is read.
  • Solved the problem that the set value of the Scaling with the Data Parts component can be changed when the project is read.

Ver.1.16 : CX-One Version 4 Auto-update (November 2011)

New functions
  • Supported NV3Q-SW**(color) PT with new LCD device.

Ver.1.15 : CX-One Version 4 Auto-update (August 2011)

Improved functions
  • Solved the problem that the verification function doesn't work properly with NV4W under special conditions.

Ver.1.14 : CX-One Version 4 Auto-update (October 2010)

Improved functions
  • Solved the problem that the keyboard screen was not displayed on NV3Q or NV4W under special conditions.

Ver.1.13 : CX-One Version 4 Auto-update (July 2010)

New functions
  • Supported GOT_NV Conversion Support Tool.

Ver.1.12 : CX-One Version 4 Auto-update (April 2010)

Improved functions
  • Solved the problem that the password with 8 characters can not be used in the password on NV3Q/4W.
  • Solved the problem that the parts attributes were not properly displayed in the Parts Attribute Display function.

Ver.1.11 : CX-One Version 4 Auto-update (February 2010)

Improved functions
  • Solved the problem that the PLC Unit No. was not properly displayed on the Address Cross Reference.
  • Solved the problem that communication errors occurred when the Units were connected in ModbusRTU mode (RS422/485).

Ver.1.10 : Version V4.* → CX-One Version 4 Auto-update (December 2009)

New functions
  • Supported NV4W PT.

Ver.1.02 : Version V4.* → CX-One Version 4 Auto-update (October 2009)

Improved functions
  • Solved the problem that the Alarm History Information could not be uploaded properly.

Ver.1.01 : Version V4.* → CX-One Version 4 Auto-update (August 2009)

Improved functions
  • Solved the problem that a text import may not be completed properly.
  • Solved the problem that a screen transfer to NV through the COM port 10 or later may fail.

Change history of CX-Thermo

Ver.4.62 : CX-One Version 4 Auto-update (March 2014)

New functions
  • Supported the E5GC.
  • Supported the E5AC-TPR/E5EC-TPR.
  • Supported the E5CC-U Ver.2.2.

Ver.4.61 : CX-One Version 4 Auto-update (January 2014)

New functions
  • Supported the E5AC-T/E5EC-T/E5CC-T Ver.1.0.
  • Supported the E5CC-U Ver.1.1.
  • Supported the E5AC/E5EC/E5CC/E5DC Ver.2.1.

Ver.4.601 : CX-One Version 4 Auto-update (October 2013)

Improved functions
  • Solved the problem that PID parameters are initialized when Compare[PC-Devices].

Ver.4.60 : CX-One Version 4 Auto-update (June 2013)

New functions
  • Supported the E5DC.
Improved functions
  • Improved the setting condition of the 'set point', if the 'multi-SP' is enabled.
  • Added the function to prevent unintentional transfers to the device.

Ver.4.51 : CX-One Version 4 Auto-update (February 2013)

Improved functions
  • Solved the problem that the additional parameters of the E5CC/E5EC Ver.1.1 may not be transferred or compared.

Ver.4.50 : CX-One Version 4 Auto-update (November 2012)

New functions
  • Supported the E5CC Ver.1.1 and Ver.2.0.
  • Supported the E5EC Ver.1.1 and Ver.2.0.
  • Supported the E5AC.
Improved functions
  • Solved the problem that setting ranges of the remote SP upper limit/lower limit parameters are incorrect in case of analog input for E5EC/E5CC.

Ver.4.40 : CX-One Version 4 Auto-update (November 2011)

New functions
  • E5EC/E5CC are supported.
Improved functions
  • Solved the problem that the parameters since program No.9 for E5AR-T/E5ER-T can not be set.

Ver.4.30 : CX-One Version 4 Auto-update (January 2011)

New functions

[Support of New Types]

  • Supported THERMAC NEO programmable type E5AN-HT/E5EN-HT/E5CN-HT.

Ver.4.20 : Version V4.* → CX-One Version 4 Auto-update (August 2009)

New functions

[Support of New Types]

THERMAC NEO basic type E5GN (release in Sep. of 2009) are supported.

Change history of CompoNet DTM

- :CX-One Version 4 Auto-update (January 2014)

Improved functions
  • Solved the problem that you could not print the data when "&" and other special characters were used in an I/O comment of CompoNetDevice.

- :CX-One Version 4 Auto-update (August 2012)

New functions
  • Supported the CompoNet communication unit for RX series inverter : Model 3G3AX-RX-CRT-E.

- :CX-One Version 4 Auto-update (February 2012)

New functions
  • Supported the CompoNet Slave device of E3X-CRT.

- :CX-One Version 4 Auto-update (November 2011)

New functions
  • Supported the CompoNet communication unit for MX2 series inverter : Model 3G3AX-MX2-CRT-E

- :CX-One Version 4 Auto-update (May 2011)

Improved functions
  • Updated the EDS files for CompoNet Devices.

- :CX-One Version 4 Auto-update (October 2010)

Improved functions
  • Supported Timeout Setting on CompoNet Master DTM.

- :CX-One Version 4 Auto-update (April 2010)

New functions

[Support of New Types]

  • Supported CompoNet CRT1B-series "Bit Slave Compact Connector type".
    Supported models CRT1B-OD04JS(-1).

- :Version V4.* → CX-One Version 4 Auto-update (October 2009)

New functions
  • CompoNet CRT1B series "Bit Slave Compact Connector type" are supported.
Improved functions
  • Solved the problem that model name of CompoNet Slave CRT1-VAD04S is not displayed correctly in Parameter, Monitor and Properties Dialogs.
  • Solved the problem that network - compare function returns error though the network structure including CRT1-VAD04S is correct.

- :Version V4.* → CX-One Version 4 Auto-update (August 2009)

Improved functions
  • Solved the problem that you can not install certain EDS files.

Change history of SmartSlice I/O Coupler DTM

- :Version V4.* → CX-One Version 4 Auto-update (October 2009)

Improved functions
  • This is a new product version of the GRT1-PRT/CRT/PNT SmartSlice I/O Coupler DTM that fixes a problem that prevents download to a slice unit if the slice has been copied and pasted

Change history of Network Configurator

Ver.3.56 : CX-One Version 4 Auto-update (June 2013)

New functions
  • Supported the FH-series Vision Sensors with built-in EtherNet/IP.

Ver.3.55 : CX-One Version 4 Auto-update (November 2012)

New functions
  • Supported the ZW-series (ZW-CE1*) Displacement Sensors.
Improved functions
  • Supported the connection setting with odd-byte Tag (including the physical address) on the CPU built-in EtherNet/IP port and EtherNet/IP unit for CS/CJ-series PLCs.
  • Expanded the communications band for each line in the multi-line random mode on FZ-series vision sensors.

Ver.3.53 : CX-One Version 4 Auto-update (August 2012)

New functions
  • Supported the FQ-series Vision Sensors with built-in EtherNet/IP.

Ver.3.51 : CX-One Version 4 Auto-update (April 2012)

Improved functions
  • Improved the print function of EtherNet/IP Datalink Tool.

Ver.3.50 : CX-One Version 4 Auto-update (February 2012)

Improved functions
  • Updated the EDS file for FZ Series and FJ Series Vision Sensor.

Ver.3.40 : CX-One Version 4 Auto-update (August 2011)

Improved functions
  • Updated the FZ Series EDS file.
  • Solved the problem that connection with same name is wrongly created on "Edit All..." function.

Ver.3.22 : CX-One Version 4 Auto-update (January 2011)

New functions

[Support of New Types]

  • Supported the Model FZ3.

Ver.3.21 : CX-One Version 4 Auto-update (October 2010)

New functions

[Support of New Types]

  • Supported for the built-in EIP Unit version 2.1 of CJ2M-CPU3[] that allows tag data link of a maximum of 640CH.

Ver.3.20 : CX-One Version 4 Auto-update (February 2010)

New functions

[Support of New Models]

  • Supports CJ2M CPU Units.
    Supports models CJ2M-CPU[][].

Ver.3.10 : Version V4.* → CX-One Version 4 Auto-update (December 2009)

New functions
  • New functions of Datalink Wizard and EtherNet/IP Device Drag&Drop have been added to simplify the Tag Datalink (connection) configuration.
Improved functions
  • Solved the problem that connection setting to 3rd party EtherNet/IP device can not be transferred to the Unit in particular case.

Change history of Communications Middleware

Ver.1.02 : CX-One Version 4 Auto-update (April 2012)

New functions
  • Supported the CP1L-EL / -EM CPU Units.
    Supported the models CP1L-EL[][][][]-[] and CP1L-EM[][][][]-[].